ericg

if you want send me your mail via pm and i'll send you the active-x .exe Thanks for your support! It is now working, after having selected "upnp" option. Thanks to Qvlogan88 for his very active and efficient support!

No way to get it installed. Can you please develop the option with a downloader?

you have to open 5051-5052-5053 then you see image in remote with IE and active-x installed with other browser i see cam only in localhost I switch back to the default port but no luck. Furthermore, impossible to register the active X which is not signed. It is a real mess!

I tried both Chrome and IE, without any luck...The same laptop works flawlessly when connected to the local network and doesn't work at all when connected from the external. I don't think it is a plugin problem. THe issue is that the NVR is useless tosurvey my house when in vacation...

I'm stuck with remote access: Port 80 is routed through my internet box via 5099 external port. I can connect to the interface, manage configuration, but no picture, neither live or playback. I have also routed 4 ports for device port set at 5099 and I have routed 5099, 5100, 5101 and 5102. But no luck... Is there an additional port to route in order to get video working?

I had to adapt in the number of stream the maximum resolution

The latest firmware version 20141030's default setting for recording is to replace oldest recording files with newest recording files. We have hide the selection. There is a firmware to disclose the selection and enable you to select between 1, erase old files and keep recording 2. stop recording when HDD is full. But I don't think this firmware is necessary to be used... Thanks Mike, this is perfect for me! I need to understand now how I should configure my internet box to get access from internet. I have setup a port forwarding from 10000 public to NVR local IP port 80. I get access to interface and settings but no video... If someone can give some indications...

I would like to say a big "thank you!" to Mike and his technician Alvin! They sort out all problem I had on my mini NVR to get motion detection to work! Main issue was the camera settings: I rely on the auto search but parameters should be forced to a specific protocol instead of ONVIF and the default port should be changed from 1018 (Onvif detected port) to 80 as default. Motion detection is now working. I need to find out now how the verious schedule parameters interfer between each other! I would like also to understand how I can delete file on my HDD or if I can setup the oldest recording to be erase by newest ones. Only option I see as of today is to format the HDD when it is full...But I surely miss something on that topic!

No, unfortunately not. You will have to replace both of your cameras.

I believe your cameras are not ONVIF compliant.....

Edit of the complete message for more clarity on my request! I'm a little bit lost with my NVR... It is updated to last FW version available from URCCTV, I have 4 cameras connected (4 channels are unused). 3 are Cybernova cameras and one is an unbranded purchased from Aliexpress. I'm trying to configure and setup everything from the IE interface, without ActiveX. All cameras were resetted to default parameters. 1/Camera setup When trying to configure the camera, I use the "search" features but it gave me different results. Here are 2 snapshot of the result, looks at the port and the protocol found: and Which setting should I use? For the camera with Protocol I9, if I keep the port 8091, I have no pictures. I have to set it to 80 to get a pictures. Is it normal? 2/I can't get the OSD to work on any of the 4 channels, no time stamp is visible from IE. Is it normal? If normal in IE, will the time stamp be recorded? If not, that mean I have to activate the time in each camera, which is a mess as they do not keep a proper time zone... 3/I can't set motion detection on any of them. Each time I change and save the parameters in the motion detection menu, when I open the menu again settings are ressted. Should the motion detection be programmed in each camera own interface or is it the NVR which will manage this? 4/I have connected a HDD (750 Go). Recording is working but I have not find any setting for the storage. I would like to overwrite automatically the oldest files once the disk will be full. Is this possible? 5/When accessing the NVR from my local network, I have pictures of the camera. But when I try to access it from outside, I have only the interface and no pictures of any cameras. I have forwarded in my router the public port 10000 to port 80 of the NVR and opened 5050 to 5052 from public to NVR IP. But I have no luck... Can you please explain how to manage this? sorry for having so many questions ))

Could the motion detection issue with the Cybernova be linked with the fact the camera are equipped with SD Card?

Mike, protocol i36 uploaded, but motion detection does not seem to work. Should I set something in the camera config or all the settings are to be applied only in the NVR? I have activated the motion detection for each channel, defined the area to monitor, set an email adress and sound alarm but nohing happen. When I come back on the setting pages, the area defined is not appearing and sensitivity is resetted to medium. Thanks for your support! Regarding the problem of password, I had the same problem. If a password is setup in the camera, no way for the NVR to detect it!

Thanks Mike, I will check it this evening.

HDMI is fine with a TV (still using HDMI to DVI cable), so it is not working with standard computer monitor. I'm now need to understand how to get movement detection with my cybernova cameras...