Jump to content

01sporty

Members
  • Content Count

    19
  • Joined

  • Last visited

Community Reputation

0 Neutral
  1. 01sporty

    Best Software- PC IP based...

    I'll take a look at it.
  2. 01sporty

    Anonymous Login

    None of my cameras are connected to the internet, this is strictly for viewing over my network. All of my other cameras just require checking the 'anonymous login' box. But, every new camera I get seems to have a different firmware so I thought this one might need something additional.
  3. 01sporty

    Anonymous Login

    I got a new camera and I can't get the anonymous login to work. It gives me this: Do I need to do something other than check the box? Thanks for any suggestions.
  4. 01sporty

    Best Software- PC IP based...

    I'd like to see some discussion on this. My needs are even simpler. I'd like to find a good viewer to replace the browser plugins. I have a Flir (Dahua) system and more and browsers are unable to run the plugin without tweaking. It would be nice to find an stand-alone bit of software for viewing from my computer.
  5. 01sporty

    Changing Camera Color

    I just sprayed mine. If you wanted it to turn out really well, you should use a plastic primer. I didn't. I just wiped them with a high proof alcohol and shot them. It did not work well on the cable but everything else is holding up.
  6. 01sporty

    Port Forwarding??

    I'm back. I checked my router and couldn't find anything like what you're showing. So, I found an AT&T forum to see what they had to say. Bottom line is my router is lacking in those kind of advanced features. Just to make sure I had tried everything, I contacted tech support at Flir. They confirmed that any cameras that are connected directly to the NVR are only visible on the NVR not on the network. That's pretty much what I expected to hear but I never hurts to check. When I purchased the unit I had assumed the 8 POE ports worked like a built in POE switch. If I had known how useless those ports are for my situation I would have bought a plain Jane unit without any ports. Even from the NVR I could find no way to directly access the camera menus. Those menus have a lot of good stuff. I wonder if this is a common situation? I haven't seen any other discussion on it. So, I was left with the hardware solution. A bit of good news there. The NVR came equipped with two power supplies. A 12 vdc for the recorder and a 48 vdc, 2.5 amp for the POE ports. I found a 7 port POE switch that can be purchased separately from the power supply and just happens to be a perfect match for that 2-1/2 amp unit that came with the NVR. I'll let you know how it works out when the switch arrives.
  7. 01sporty

    Port Forwarding??

    Here's something you may or may not find interesting. In the Firewall/NAT/Gaming tab, there's something called Service and Needed by Device. In the Service dropdown there are a bunch of games and things like SMTP and Pop3. In the Needed by Device dropdown, a bunch of my stuff is listed. The last four are the NVR and the three cameras that I can access. Under that is Manage Custom Services. Is any of this helpful?
  8. 01sporty

    Port Forwarding??

    Cool. It's a Motorola NVG510. AT&T. Let me know if you need any screenshots or whatever.
  9. 01sporty

    What do you make of this cat6?

    Another trick I found very useful is to buy a length of 3/8" copper tubing. When going through walls or floors or across spans you don't want to walk or crawl across, you use the copper tube. Examples: I needed to string cable across the attic of my shop and didn't want to wade through the insulation. I uncoiled the tube out over the top of the insulation then pushed the cable through. When done, I pulled the tube off the cable. I had another place where I needed to go through the floor. Again lots of insulation to get through. I cut a 1 ft. piece of tube, flared the end so it couldn't drop through the 3/8" hole I had drilled, then pushed it through the floor. When I got to the underside of the floor, it was easy to find my hole and push the cable through it. Just be sure you debur the tubing so it doesn't shave the cable.
  10. 01sporty

    Port Forwarding??

    While you're there, there's a file called: IP-Cameras-Networking-FAQ_EN_R1.pdf My setup is just like 'Scenario 2: 8-Channel NVR with 4 PoE Ports and 8 IP Cameras'.
  11. 01sporty

    Port Forwarding??

    RS232: Service only; not in use. That's a quote from the manual. The RS232 port is there but there is no telling how useful it is. The manual is very good at going over the obvious in great detail and keeping the hard stuff secret. Typical. Here's a link to it: http://www.flirsecurity.com/pro/product/dn308p2e6-hd-poe-nvr-ip-camera-security-bundle/
  12. 01sporty

    Port Forwarding??

    Your NVR is hosting LAN1 and a 192.168.1.0/24 network handing out DHCP addresses to your cameras. No. My LAN1 is my router. Until this last camera, everything has been handled by my router. It has given everything addresses of the form 192.168.1.xxx. This includes all of the cameras and the NVR. Your 10.x network is your regular internal LAN for all your computers and other devices, and the 10.x net is hide natting behind your internet connection. No. The 10.x network was created by the NVR. The last camera I installed was the first camera to be plugged directly into the NVR. It was assigned an address of 10.1.1.xxx. I'm not sure what the internal address is of the NVR but I suspect it's 10.1.1.1. And, I suspect it may actually be a switch. Can a switch assign addresses? Maybe its 8 ports have permanent address assigned to them? I say this because of this setup page. The IP Address, Subnet Mask and Default Gateway values all can be changed but I'm very hesitant to just start trying stuff. I'd really hate to lock myself out.
  13. 01sporty

    Port Forwarding??

    goodolick, Boogieman, Thanks for the replies. There are 5 computers on the network. Getting each of them talking to the new network sounds a bit tedious to me. I was really hoping for a way to get the two networks talking to each other so they act as a single network.
  14. 01sporty

    Port Forwarding??

    Ok, the more I think about it and read about it, the less I think I need port forwarding. I do think I need something similar. I think the NVR is acting like a router and has set up it's own network. I just need to get the two networks to talk to each other. Sounds easy until you get into the particulars. Here's a discussion of a similar problem: http://www.tomshardware.com/answers/id-1647778/connect-lan.html The solutions are far ranging from 'sounds simple' to 'really? you want me to add another router?'. This discussion sounds more hopeful: http://www.makeuseof.com/answers/connect-networks-ip-addresses/ I don't really understand it yet but when I get more time, I hope to see if I can't get it to work with my system. I'll try and get some screenshots to post.
  15. 01sporty

    What do you make of this cat6?

    Well, it does get easier the more you do it but I'm not sure I'd ever call it 'easy'. If you haven't already, get something like this: hhttp://ttp://www.ebay.com/itm/RJ11-RJ12-RJ45-CAT5-UTP-NETWORK-LAN-USB-CABLE-TESTER-/111317477857?pt=LH_DefaultDomain_0&hash=item19eb09e9e1 If the camera isn't immediately found, eliminating a bad cable as one of the variables is more than worth the cost of the tool.
×