Jump to content

Leaderboard


Popular Content

Showing content with the highest reputation since 01/30/2019 in all areas

  1. 2 points
    Hi. No don’t update Remove your no ip account Your using the Apollo ... good system Delete your no ip and follow the link I have sent to your PM Much more secure and protected
  2. 1 point
    I bought Dahua DH-IPC-HFW1320S IP camera on eBay, and I have problem setting up FTP upload of recordings to FTP server. Here are my settings: For remote directory I used "/", "/test", "test" or leave blank and results are always same. This log entries shows that motion detection was triggered For first I used ftp server on internet, later I started filezilla ftp server on my pc. This is log form FileZilla FTP server. (000010)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> Connected on port 21, sending welcome message... (000010)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> 220-FileZilla Server 0.9.60 beta (000010)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> 220-written by Tim Kosse (tim.kosse@filezilla-project.org) (000010)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> 220 Please visit https://filezilla-project.org/ (000010)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> USER test (000010)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> 331 Password required for test (000010)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> PASS **** (000010)10.2.2017 3:32:07 - test (192.168.251.213)> 230 Logged on (000010)10.2.2017 3:32:07 - test (192.168.251.213)> PWD (000010)10.2.2017 3:32:07 - test (192.168.251.213)> 257 "/" is current directory. (000010)10.2.2017 3:32:07 - test (192.168.251.213)> disconnected. (000011)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> Connected on port 21, sending welcome message... (000011)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> 220-FileZilla Server 0.9.60 beta (000011)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> 220-written by Tim Kosse (tim.kosse@filezilla-project.org) (000011)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> 220 Please visit https://filezilla-project.org/ (000011)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> USER test (000011)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> 331 Password required for test (000011)10.2.2017 3:32:07 - (not logged in) (192.168.251.213)> PASS **** (000011)10.2.2017 3:32:07 - test (192.168.251.213)> 230 Logged on (000011)10.2.2017 3:32:07 - test (192.168.251.213)> PWD (000011)10.2.2017 3:32:07 - test (192.168.251.213)> 257 "/" is current directory. (000011)10.2.2017 3:32:07 - test (192.168.251.213)> QUIT (000011)10.2.2017 3:32:07 - test (192.168.251.213)> 221 Goodbye (000011)10.2.2017 3:32:07 - test (192.168.251.213)> disconnected. So, communication is ok, camera can access and login to ftp server, but why that camera wont upload anything? I also tested NAS as storage, and everything that I got is that camera can create folder on NAS. What can be wrong here?
  3. 1 point
    Hello I bought a model VTO2000A Videophone intercom. I accidentally Entered the wrong password three times. Unfortunately I can not get in because i scive blocked user. How can I return to factory reset? very kind people who want to help thank you
  4. 1 point
    Not banned outright until August 2019 then imports will be a problem They messed up last month ..... now homeowners are starting to see the security problems and being warned setting up for internet with there own passwords and usernames and one day logging on only to find someone else’s system one couple have found there home cctv system showing live on a website its not just a government problem it’s a homeowners problem which is worse security cctv should not involve a 3rd party
  5. 1 point
    It is confusing hikvision can’t keep anything simple ... hikvision turbo 4.0 is stated to be POC ... that is not the case when you look at specs .... take your model number HIKVISION DS-7204HUHI-K1 why do hikvision find it so hard to to simply add POC at the end HIKVISION DS-7204HUHI-K1 -POC same with the comparable cameras if you are installing your system coax with power (shotgun) is just the same as feeding coax and does not leave your system to being POC only poc systems you can’t use existing cameras if you have a problem you can only replace with POC proprietary systems are pointless and don’t stay on the market long
  6. 1 point
    Also note that the HUH can also take more additional IP cameras if desired. So the long and short of it is that the HUH is the more capable recorder.
  7. 1 point
    To add to this, that 12x Dahua zoom mentioned is really a varifocal camera. It is used during setup of the camera. The zoom is usually painfully slow. And bullet cameras attract spiders that spin a web right in front of the camera, setting off the motion detection. I am out probably three nights a week clearing webs from 2 bullet cameras. My 2 dome cameras have no problems with spiders. I keep them under a soffit and rarely have to clean water spots off, only after a very windy rain blows through. Eyeball or turret cameras are supposed to not have those problems.
  8. 1 point
    hd908 seems too relaxed to be boogerman/fenderman.
  9. 1 point
    Aside from NVR compatibility, when I did my research I found the low-light camera to beat is still the Dahua IPC-HDW5231R-ZE 2MP Starlight. Outdoor usage: Check. Good low-light performance: Check. PoE: Check. $100-$200 USD: Check. It's manual pan/tilt. It has motorized zoom. I'll be using mine with Synology NAS Surveillance Station software... maybe. (Their notification mechanism is currently thoroughly broken. If they don't get it fixed, I'll have to find another solution.) N.B.: I have not installed this camera yet. It's wintertime, here, and I don't feel like hacking on our vinyl soffits and crawling through the attic in sub-freezing temperatures, or tracking snow, slush and mud all over creation.
  10. 1 point
    Hi. It depends on which nvr you are going to use . It needs to be compatible some nvrs are only 2mp recording some are 5mp or 4k
  11. 1 point
    As far as I understand, FreePBX is simply a project adding a working webIf to asterisk. So everything should work as it does with a base asterisk. I run a asterisk on raspbian, no special version, just the stuff that you get with apt-get.
  12. 1 point
    Hi. No need to take anything down .....your network is only used for remote viewing with only using two 5mp your ok but I would look at adding later 4mp and even 2mp is small areas or you will need to drop FPS also remember you can use any tvi camera or 4 in 1 camera does not need to be hikvision if you have not bought anything yet I would pic TVT over hikvision security industry had another report yesterday on hik hack
  13. 1 point
    There are two ways to go about this: Find the output current rating on the power supply (I assume the Lorex NVR powers the cameras?) and multiply that by its output voltage. That will give you its approximate max wattage. UPS' are rated in VA (volt-amps), but it'll be close enough. The other way is to actually measure the current draw on the AC side using a true RMS ammeter. (That's the best way.) Then multiply the measured current draw times the line voltage. Next you have to determine whether the point is to protect your surveillance system and allow it to survive short-term outages, or to have it stay up for an extended time when there's an outage. (I note you list a "12V 10" PSU. If that's 12V at 10A, which would probably be about right for an 8-camera system [assuming about 15W/camera], then your want a minimum 120VA UPS. Depending upon the design, that may give you anywhere from 5-10 minutes of uptime [SWAG]). To a degree you can extend uptime by going with a higher-than-recommend-VA UPS, but there are diminishing returns with each bump in VA capacity. Reason is reduced efficiencies as UPS VA capacity goes up. For truly extended runtime you need an "extended runtime" UPS. They don't have greater VA capacity, but more battery. (They also take longer to recover because there's more battery capacity to charge back up. There ain't no free lunches.) E.g.: With a 120W load, a 120VA UPS may give you about 5-10 minutes of uptime, but a 360VA UPS won't necessarily give you 15-30 minutes. In fact: My old power-hog Dell 1600SC server had a 700VA APC SmartUPS on it. The computer + peripherals drew about 200W. The UPS had a runtime of only fifteen minutes with brand new batteries. Speaking of batteries: Make sure to buy a UPS with user-replaceable batteries. They have about a three-year lifespan. Also: Get in the habit of doing run-time tests about every quarter or so, to extend battery life. The UPS manufacturer should have a chart listing estimated run times for each of their UPS' vs. expected loads.
  14. 1 point
    I uploaded it here: VTO+VTH multilingual firmware I hope the "chinese-portuguese" is better than the "chinese-german"... If you don't like the sounds in your language, you either step back to an old SIP firmware as I did (where you are still able to personalize every sound file!) or you wait for a working V4 firmware, where you are at least able to deactivate the sounds. Too bad, that dahua does not implement a "sound" upload option. I guess, this would not be hard to implement but it would make this little device the only one on the market with such options.
  15. 1 point
    No .... if you come on with camera awful then there has to be a reason. calibrating is done on the camera ... it’s done while installing does zoneminder do 4k yet ? does it do h265 ? RTSP ..... I think you will find onvif is the best way explain why you should defend h264 ? Are you using 4k Why ..... because you don’t like to hear that your cameras are not compatible with what you using with them. So your expecting 8mp/4k on equipment that can’t get you there You will need to load software for cam onto pc then go into settings .....being on zoneminder I would also drop resolution down to 4mp .... not 8. Then go into camera zoom and move far out then in and then set it to distance needed then click save
  16. 1 point
    Well that’s your problem........RTSP stream. Why are you messing around with VCL also no camera functions with zoneminder also running at wrong compression. its easy to blame the product....than to set it up right. and to give you a hint on not setup your images are nothing like 2mp never mind 8mp
  17. 1 point
    Hi. Rain or snow does not have to have contact with sensor. .... so just sensor under cover will not help I would forget trying to get a pir sensor to work at that distance. I would look at GJD wireless pir heads. Very reliable and last 4 years on one 9v standard battery Mount pir at your gate ..... set detection patern..... also control on and off and schedule from recorder http://www.gjd.co.uk/products/wireless-detectors
  18. 1 point
    Hacked twice Russia and from Argentina
  19. 1 point
    Problem solved! The daughter bought the same style camera with WiFi and her new boyfriend put up a pole made out of 1 3/4" plastic pipe. He mounted the camera to treated wood and attached it to the pole and placed it right next to the neighbor's camera but in my yard. Now she can't see his camera from the window and she has a great view of his rear patio. Haven't heard a peep from him yet. Nothing illegal and nobody got hurt!
  20. 1 point
    The problem with that is he can also switch it on and off when he likes
  21. 1 point
    I don't know about re-loading the firmware, but if you need to re-set the passwords, you can use the clearparam command as described in the opening post. telnet into the camera, then type /sbin/clearparam This will do a 'factory reset' for all of the camera parameters - it will clear any user accounts that you may have created, and it will restore the camera default settings (passwords, ip addresses, overlays, etc). When I ran this the process seemed to hang (as it has changed the camera ip address, and so the telnet session was mangled). But after waiting for the camera to re-appear as 192.168.1.108 I was able to access the GUI using admin and the default admin password. -- Chris Unfortunately, since I changed the Admin account password to a password I cannot recall, I can't enter the SSH/Telnet area to run the /sbin/clearparam command... -EP
  22. 1 point
    I don't know about re-loading the firmware, but if you need to re-set the passwords, you can use the clearparam command as described in the opening post. telnet into the camera, then type /sbin/clearparam This will do a 'factory reset' for all of the camera parameters - it will clear any user accounts that you may have created, and it will restore the camera default settings (passwords, ip addresses, overlays, etc). When I ran this the process seemed to hang (as it has changed the camera ip address, and so the telnet session was mangled). But after waiting for the camera to re-appear as 192.168.1.108 I was able to access the GUI using admin and the default admin password. -- Chris
  23. 1 point
    Usually the AN-TONE DVRs have a Jumper on the PCB Board front panel side. When the DVR is ON, short the jumper for 10 sec. Reboot the DVR and you have the Original User / passwords (Admin / 888888) * Note. on Admin user A should be capital.
  24. 1 point
    I Seen this nasty mess today............. Oh wait a minute, this is my system
  25. 1 point
    I have to say that the standard of CCTV work I have experienced in the UK is very good in the main. I have learned a bit from remedial works, I have seen the way other's do things and in some cases I have changed the way I do things because I have seen a better way of doing something.
This leaderboard is set to Chicago/GMT-05:00
×