Jump to content

Kalip

Members
  • Content Count

    31
  • Joined

  • Last visited

Everything posted by Kalip

  1. I am thinking of adding a camera to my CCTV system. (I know that there are standards or codes in electrical wiring) Are there any colour codes for Video Balun Transceiver and Power Supply wires when using CAT5 OR CAT6 cable to install CCTV HD Analog Cameras?
  2. I noticed that on a rainy night just after midnight to a few minutes after 6:00 am that 3 of the 6 cameras on the CCTV system stopped showing and recording however they work fine in the daylight. One of the functioning ones was grainy and showing intermittently. I have identified the offending camera. When I turn on the lights that camera along with the others are functioning. When I disconnected that camera, the others are working fine with night vision. I am wondering why the issue with the problem camera is affecting the other cameras on the network. Does anyone have any idea what could have caused this problem?
  3. When installing a camera, is it necessary to use all 3 pairs of remain wires in cat5e cable for the power supply as shown in this diagram?
  4. Thank you for your response
  5. I am using a 12V-13.8VDC Output Security Camera Power Adapter to power 2 of my cameras Will using the power supply set at 13.8VDC cause any damage to the cameras or DVR? The cameras are located about 10 metres from the DVR
  6. Does anyone know what amperage powers supply is required to power two of these cameras? The manual is silent on this issue. https://www.hikvision.com/en/Products/Analog-Camera/Turbo-HD-Camera/5-Mega-Pixels/Outdoor-Dome/DS-2CE56H0T-ITMF
  7. Kalip

    Powers Supply Amperage

    .I tried using this 2.5 amp. power adapter splitter to power both cameras. However, I noticed that I am getting ground loop problems. When I used two separate power supplies the ground loop problems stopped. Are these power splitter power adapters any good? On another note, I noticed is that the guy who installed the other 5 cameras used an “EPCOM DC ADAPTOR MODEL PS120DC4C” power supply 5 AMPS Although the adapter says 4 channels, he doubled the connection on one terminal to accommodate two cameras on that single terminal. Is this normal?
  8. Kalip

    Powers Supply Amperage

    Thank you for your response.
  9. Kalip

    Powers Supply Amperage

    Is it necessary to use all 3 pairs of remain wires in cat5e cable for the power supply as shown in this diagram? The cameras are just a few metres from the DVR and the cat5e cable is about 12 to 15 metres long
  10. Kalip

    Powers Supply Amperage

    Thank you for your response I want to add 2 of these cameras to my system.
  11. I am looking for a 5mp Analog varifocal Hikvision turret or dome camera. An Amazon merchant emailed me saying he has a Hikvision OEM varifocal Camera. He said “The camera is manufactured by Hikvision however, it does not have logo or brand and the box is plain brown box.” What’s the difference between the Branded Hikvision and the OEM version? And would it be compatible with the Hikvision DVR 7208 that I am currently using?
  12. Kalip

    Hikvision OEM HD Camera

    Thank you for your response. Forgive my ignorance, I am a novice to CCTV but is the HDView brand Camera any good?
  13. Kalip

    Hikvision OEM HD Camera

    My current CCTV system is a Hikvision I just wanted to add a camera
  14. A CCTV Installation guy told me that since normal HD monitor only has a resolution of up to 1080P. (1920 X 1080) it makes no sense installing a 5 MP Turbo HD Analog surveillance system if you’re not using a 4K monitor with it. (As I understand it the 5MP has a resolution of 5MP 2560x1920.) Is this really the case?
  15. Kalip

    Monitor Quality

    Thank you for your advice. I don’t think that the remaining areas would need plate recognition although face detection may be an advantage.
  16. Kalip

    Monitor Quality

    Thank you very much I checked the frames per second on the DVR and the manual and you are right. I am using the Hikvision Turbo 7208 DVR and it adjust the frame per second according to the megapixel of the camera, in this case for the 5mp camera the maximum frame per second is 12. At 8mp it would be 8 frames per second, for 3mp it would be 18 frames per second and so on.
  17. Kalip

    Monitor Quality

    Thank you for your responses. I already have four 5mp Turbo Hikvision varifocals installed. There are 3 or 4 additional cameras yet to be installed and he’s trying to convince me to use 2mp for the rest of the areas. I shall insist that he installs at least 5mp cameras in remaining areas.
  18. Kalip

    Monitor Quality

    Thank you for your response.
  19. I was having a recording problem with my Hikvision Turbo DVR 7208. The installer took away the Hikvision DVR and temporarily replaced it with a Longsee DVR (until the Hikvision DVR is returned from the supplier). All 5 of the Hikvision cameras are working fine with the Longsee DVR.
  20. I had a CCTV system (analog) installed at my home a few months ago with 5 5 MP analog cameras. However, I am not quite satisfied with the performance. The Hikvision Technician who installed it told me that IP Systems show up to 4 times clearer than the CCTV. Is the quality of the IP system so much better that it’s worth upgrading from analog?
  21. Thank you for your response I have submitted hereunder the display that I am seeing on the screen: (Thanks for the clarification also, I had erroneously stated facial recognition what I actually meant was facial detection. ) Camera Resolution 5mp Resolution 5MP Frame rate 12fps Maximum bit rate kbps 2048 Maximum bit rate recommended 1852-3087 kbps Maximum average bit rate 1440 Encoding H.265 The DVR atomically sets the frame rates to 12 fps at 5 MP, 15ffs at 4MP and 18fps at 3MP NOTE The frame rate cannot be adjusted upwards.
  22. Thank you both for your responses Listed hereunder are the specifications of the equipment used (to the best of my knowledge): DVR: DS-7208HUHI-K1 TURBO HD DVR 4 CAMERAS: DS-2CE16HIT-IT3Z 5MP 2.8MM TO 12.MM (MOTORISED LENS) TURBO HD 1 CAMERA: DS-2CE56HOT-ITMF 5MP 2.8MM TURBO HD. According to the PTZ settings and the DVR settings the cameras are set to 5MP (I don’t know if I was expecting too much from the system. The coverage is fairly okay, but facial recognition is not that clear.)
  23. Thank you for your advice.
  24. A DS-2CD2055FWD 2.9MM 5mp Hikvision IP camera to the network but the NVR receiving a VGA signal from it. I tried another 5MP cameras on the same connection and the NVR is receiving the correct 5mp signal. The option with camera to change the signal on settings with the DS-2CD2055FWD on the NVR are 640X480 VGA and lower. The options with the other camera are from 8MP and lower. Does anyone have and ideas how to resolve this issue?
×