Jump to content

Numb-nuts

Installers
  • Content Count

    1,995
  • Joined

  • Last visited

Everything posted by Numb-nuts

  1. I wonder that you ask for advice at all, you certainly don't listen to the advice. I don't doubt your electricians abilities, as an ELECTRICIAN. CCTV uses signalling which electricians are not often trained in You don't want advice, you want someone to tell you what you want to hear.
  2. If you are getting a CCTV system and would rather spend a bit more on the equipment to make sure you are not disappointed yet you get an electrician to install it? CCTV is based on signalling not electrical circuits and I have just had to rewire an entire 16 channel system that a well meaning electrician installed and finished up with loads of ground loops infested images a DVR without even a hard disk drive in it and wired with copper coated aluminum cable. I would no more take on wiring a house than an electrician should do CCTV. Both completely different. Would you take your car a car valet to get the brakes serviced? Why not,They both know about cars don't they? Do yourself a favour and get a CCTV professional that can recommend proper equipment, not just connect up whatever you tell him to buy. You are on the road to a disastrous scheme and it'll be your fault.
  3. Numb-nuts

    Selling my house

    What makes you think they may be discussing anything illegal? If you are suspicious of who is coming in then you should get a different real estate agent that you can trust or be there at EVERY viewing. I really fell for THAT one didn't I?
  4. Numb-nuts

    Ground Loop Issue?

    Baud rate is usually associated with communications RS232 RS485 like on a PTZ camera and it's set a the device end so the DVR must match. What I was referring to is the Bitrate which you will find under the encode menu VBR is variable bit rate CBR Capped Bit Rate
  5. Numb-nuts

    Ground Loop Issue?

    DVR1 power supply DVR2 bit rate or hard drive
  6. Numb-nuts

    where to start wired or not?

    Use Cat6 cable (duct grade) solid copper UTP (unshielded) with proper Cat6 RJ45s to prevent potential crosstalk issues Join to the cameras inside IP rated junction boxes and make sure that you can get the connectors into the box through the apertures / gland holes. You may have to modify the boxes a little to get the benefit of waterproofing your connections. The cat6 connector on the left has staggered conductors which are staggered using a loading bar also the IDC teeth are half longer and half are shorter The cat5 on the right all conductors are on the same level.
  7. You may be better addressing that code to Dahua...
  8. Numb-nuts

    onboard rj45 port

    Correct settings should be with DHCP disabled (that is, unchecked). And use 192.168.1.1 and 8.8.8.8 as DNS servers. That is unless you can reserve the DVRs IP in the DHCP (reservation table) which will reduce the chances of IP conflicts, then it won't matter if it's selected or not but frankly it IS better to leave DHCP unchecked (or on some DVRs select static) as advised (Not all routers will allow you to reserve an IP address to a specific device)
  9. Numb-nuts

    Firmware issue

    The only way to resolve firmware issues are to reload the correct firmware or a correct upgrade firmnware from the actual manufacturer It is Unlikely you are going to track that down and if you do load the wrong firmware kiss your DVR goodbye. The only thing you'll be able to salvage is the HDD and the experience to buy from a well supported manufacturer not some here today gone tomorrow supplier from a city you can't even pronounce.
  10. Try your cables both BNCs and power cable terminations. At the dVR end simply move them about and inspect them closely Look for efflorescence (salt corrosion) at the camera end either on the connectors or in the cables. Inspect the camera to see if water or moisture has infiltrated (unlikely) If your camera is supplied exclusively by a single power supply swap it out with another to see if the problem moves to another camera. Keep a record of all the things you try which will help you in eliminating the fault eventually.
  11. What is the voltage at the camera? How have you connected the camera Cat5 with Baluns or Coax? Have you tried the camera over a very short cable in the house perhaps?
  12. Numb-nuts

    RJ45 Surge Protection?

    Okay Okay Its's CHEAP happy now?
  13. Numb-nuts

    I have a stalker and I need help

    sorry removed comment as already dealt with by previous posting.... not helpful
  14. Numb-nuts

    RJ45 Surge Protection?

    ITS NOT CHEAP...
  15. Numb-nuts

    PLEASE HELP

    WHY is it connected to your computer? You should just connect to your network (router) and connect to your computer across the network using the DVR's LAN address. You can go to http://www.portforward.com for comprehensive instructions of how to port forward your router listed by make and model number. You will also have to deal with the question of is your broadband dynamic or static, chances are it's dynamic, then you are going to need a DNS account. Good Luck...
  16. Numb-nuts

    Wiring for a full system update

    If your existing wiring is Cat5 and baluns then the obvious choice will be HD CVI as it can use either coax or standard analogue baluns but again if the cat5 is poor quality eg CCA or CCS you will suffer from poor signal then a rewire again with pure copper. I have not seen the Dahua range of HD CVI (don't ask what it stands for I'll only have to look it up again) but I have heard they are VERY acceptable and as you'd expect reliable too. But Which one to choose, CVI or TVI ????????????? good luck
  17. Set the DVR to static un-select DHCP and give the DVR a local IP of 192.168.0.(100-200) Turn UpnP off in the router and apply then on the superhub go to advanced and choose DHCP> DHCP Reservation and reserve the address to that device. Go to Port Forwarding and create rules and allocate to the DVRs IP address .ie. 192.168.0.(100-200) and apply go back to upnP and turn on and apply Your ports should now report as open
  18. Numb-nuts

    New install - bad image

    windy? I hadn't noticed.
  19. Numb-nuts

    New install - bad image

    A single pair for video white stripe+ve solid colour -ve Then take the remaining pairs and separate into whit stripe and solid color and use to carry the DC Power. My convention is everything that is white with a color stripe is +ve everything with a solid color is -ve. The fact that you are using a single pair for power means there is not enough power getting to the cameras this MAY be your problem but it will certainly need correcting before you can move toward a solution.
  20. Numb-nuts

    New install - bad image

    The cable is probably NOT your problem its the name Floureon, THATS your problem.
  21. Numb-nuts

    Help with 2 QVIS DVR on same network

    If you have 2 DVRs on a single network range, before port forwarding the Draytek you should reserve the IP address of BOTH DVRs I also notice you have the same RTSP port on both devices. One port serves one device only. It's like two fat ladies trying to get through the same doorway only onewill succeed
  22. Numb-nuts

    Swann teething issues

    Get a Windows Laptop or a real DVR
×