ybarakov

Dear Colleagues,

Unfortunately after suggested firmware upgarde I have bricked my camera.

Upgrade was suggested because of not functioning PTZ functionality, after discussing and remote testing the camera by technician from the escam company. I do not blame him, since each firmware upgarde is on each own risk.

Camera is not operative, LAN port is stil blinking, IR LEDs working. I have read topic for debrickong the Dahua camera, however I am experiencing problem in identification of IP address of the camera.

Tried conecting the camera and computer with lan cable, checking the previous IP address (camera was used only with WIFI, I am not sure whther last wireless address is the same as of LAN one.) Tried with 192.168.1.188 without success, several restarts were done, several resets also-no success.

Thank you for oyur support in advance.

Best regards

Hi,

I do not know why, but I am not able to do anything: nither to logon, nor to retrieve the password.

How it works, actually? My e-mail is requested or?

Hi,

Does someone experience problems in logging on goolink.org?

I am not able to do anything. I am almost sure that entered several days ago, now is im possible.

Niether new registration, nor password retreival.

BR

Guys,

How I can access NVR outside my home network?

External IP and 5050 if the port is opened in the router?

Hi ybarakov,

HDMI is not compatible with all TV's, works fine on my 1080p samsung but not on my older 1080i samsung.

How are you trying to record?

manual or via schedule?

Hi CharlieB,

Again thank you. NVR start writing on HDD, now HDD also visible vie WEB.

I have tried on my pc monitor with TV also, but resolution it have is not 1080p.

Probably, later on I will try on full HD TV Samsung C750. I think it will work.

About the recording:Manual recording all days 24 hours.

I am not sure how to set it up in order not to record 24 hours, but just on event.

The problem is how to set it up.

I am a newbie in that area, and thanks God this forum exists.

just too add if you plug in an unformatted or incompatible format drive the nvr will auto format anyway so don't think that is the issue, can you screen shot the nvr drive screen ?

Hi, thank you for the proposal, however the effect is not ok.

HDD is seen in the NVR in direct mode (not via IE web browser), it allows me to format it, which takes less that 5 sec. and NVR wants to be restarted. After restart nothing happens, there is no change, no sound nothing.

After attaching the HDD to the computer it did not manage to recognize it and suggested to format it.

After attaching to NVR after many times unsuccessful tries, I have manged to make screen pictures, but nothing.

It stays in the initial screen.

I also notices that network is not every time properly working. Many times you have to restart the NVR (switching off and on) until you see green led in the LAN card blinking. Many times only yellow led is blinking and there is no contact to NVR.

I have hard coded the LAN setting to the NVR and option DHCP is not ticked.

I am starting to regret having purchased this s***t.

Also HDMI port is not functioning.

hi ybarakov , try removing camera save and reboot then auto detect camera again and use admin as user but DO NOT add password.

I use 4 local escam q520's on I12 and they all connect without a password.

Nice suggestion!Thank you, it works.

I have managed.

Now I have two more questions:

1.Is it secure not to have a password in the camera?

2.How to tackle the issue with the HDD? It doesn't work.

I have tried, but it still appears as 1.8 TB disk.

I will check out HDD and will post result.

I am also posting a snapshot of settings. By chance you can find the problem , which is not obvious for me.

Despite hard coded IP in VMS for wired interface, escam camera is connected via WiFi having 192.168.11.124 IP

Can't see mistake.

Hi,

yes, You are right.

Port is 34567. Tried, but without success.

Tried also to format the HDD, nothing happened when pressing format button.

Thank you for the support.

Actually I am a little doubtful about which number to be inserted in NVR – one is saying 234567 (can’t remember the title of the port), another one is HTTP which is default 80, I have set it 8088. I have tried with both, but without success.

Also tried with admin and password and with global username and password-without success.

Anyway, I will examine in details and will provide feedback.

Just one question: if there is no camera “attached” to the NVR, I suppose no records will be available, is it?

How to format the HDD(3.5’ WD Green) in order to be acquainted with the NVR? Currently HDD is having NTFS, I see that HDD starts working with powering on the NVR, but after couple of minutes turning itself off.

Dear All,

I am pretty new in this forum, sorry for the probably stupid question, however I have the following problem I would like to request support for:

I have ordered "black" no name NVR, firm 20150808. Managed to get in and to set up the network. While still waiting other camera from China, I tried to connect with current one I have at home ESCAM QF001, which appreas to be not ONVIF compliant.

NVR managed to find it, but no pucture is available. Protocol detected is I12.

No records are possible yet. No changes were done in the router, i.e. no port forwarding done yet.

Thank you and Best regards