mastertheknife

hehe. Need to replace the coax cable with new, attach a small plastic box behind the stand to make the connections inside (this way its weatherproof) and run a PVC between the box and the electrical duct Also, is a dome camera more suitable for this location? Its less visible and can be mounted nicely (with simple drilling to the top of the metal roof). Also, this is the image from the camera after relocating the cable out of the electrical duct. Looks similar to other (identical) camera. mastertheknife

Its pretty strong and long-lasting actually. Although at first i only considered it a temporarily solution, the other camera is mounted like that for about 1-2 years now without any removal or re-tightening. The cable is a ~12-14 gauge solid core and is hard to bend. mastertheknife

I just tried something. I removed the cable from the electrical duct (had nothing inside except cat5 ethernet, rg59 and 12vdc) and its now running directly from the window to the camera. The interference is now almost non-existant. I guess the cable is bad and picking up interference. mastertheknife

Hi thank you i will try that. No its not a high voltage wire (running it like that would be dangerous!). Its just 12VDC. the power supply is behind the window next to the DVR. This is ~14 gauge and is probably an overkill for this but thats what i had in the backyard. The cables are currently going through a mess and through the window because the existing hole is full and this is reinforced concrete (30-40cm) so drilling a new hole requires a professional so until then its through the window :/ The cable is RG59 (not the foil type one) and the connectors used are 75ohm BNC from valley-ent: http://www.valley-ent.com/pics/S1B12.jpg Also, theres something funny about this camera. I can't remove the stand without cutting the video and power cables. If i cut those, can i solder a new coaxial (with female connector) cable from inside the camera or is there a better solution to this? Thanks again, mastertheknife.

Hi, the other camera has its own power supply, soo each has its own power supply actually. I tried swapping the power supplies but no difference. Disconnecting the other camera from the DVR doesn't solve the problem

Here are pictures of the way the camera is currently mounted (click to zoom): The DVR is right after this window. mastertheknife

Also, the cable is not kinked. I tried playing with the cable but no difference. How likely is it to be the cable?

There are no screws at all at this moment. the camera is simply tied strongly to the metal roof.

Yes. I tried the camera next to the DVR prior installing it at the current location. It worked nicely. Also, when plugging the camera to the TV, this interference is still there, but less noticeable. I tried powering the camera at the spot with a different power supply (12VDC 1A), same issue. I'm leading to think its interference from the metal roof or something, and perhaps the pieces of paperboard i used to as temporarily isolation from the metal roof are the problem, although it did good job in solving the rolling lines (from bottom to up at AC frequency) mastertheknife

Not possible. My power supply is 10A 12VDC and only the camera is connected. Voltage is 12.7V. I also tried 13.5V but no difference. Power cable is 14 gauge. mastertheknife

I have 2 identical cameras i bought from ebay about a year ago. These have 520TVL Sony CCD inside them. Few days ago i decided to install the 2nd camera (was unused all this time). connecting it to the DVR or TV with a short cable yields great picture. I mounted the camera at its target location (under a metal roof) and ran temporary cables (12VDC power and RG59 coax, both less than 8 meters) to inside the house. The temporary cables don't go anywhere near fluorescent or AC cables. the minimum distance from AC is around 30 centimeters. I was getting extreme interference (rolling lines at AC frequency) at first but then isolated the camera from the metal roof by using spacers and it solved the problem. However, i'm now\still getting a different type of interference. a less serve interference and seems to be diagonal. I tried re-doing the connectors and using different 12VDC power supplies. No luck. Its important to note that the DVR is actually a PC and is using the same power outlet as the power supply. The metal roof is grounded, i'm not sure at which point, but when measuring with my multimeter the metal roof to ground, its definitely grounded somewhere. Here is a picture of the interference (the camera on the right is the one) - click to zoom: mastertheknife.