dechowireless

Are you in Houston, TX? I'll get it installed for you and you don't have to lift a finger! Haha

Negative roger

Meye

Ive tried everything to solve this problem.. no dice anyone have any suggestions?

i really don't want to send this back

There has to be someone who can help!?

Help I need a super password can anyone give me a pass for today or tomorrow thank you very much

Thanks guys for all your help

Can some generate me a password for today 9-27-13 thanks

Hello i have a DVR1604HD-L and i have installed all 16 HDSDI cameras to it everything works correctly but from time to time certain cameras would blink out for like 2 secs. I wonder is its the power so i went to buy a brand new power supply box each one of these cameras without IR take up 300mA with IR on it takes 900mA i have 2 power box one is 10A 9CH and the other is 18CH 11A the 10A is a off brand power box and the 11A is an ALtronix SAV1820. i dont think the power is the issue but i could be wrong... there are 6 cameras going into the 9CH box and 10 cameras going into the 18CH box... i calculated all the power ratios and its all correct. Now i wonder if its the compression of the DVR.. i dropped all the videos down to 720P @ 14fps and now i only get 2 cameras that blink... please help if you ever encountered this problem... thanks

What type of RG59 are you using?

Extracted from Videcon SDI camera brochure

Important - Please Note

For HD-SDI installations, we recommend that this device is used with RG59 cable, with an inner

conductor made of bare copper, with a minimum diameter of 0.7mm. Using a copper clad cable,

or one with a smaller inner conductor, is very likely to reduce cable lengths or cause signal loss.

Using the recommended cable should ensure that cable lengths of 100 metres can be achieved.

thanks!!

Since you have every camera at 2k, do you still have the problem?

still have the problem.. im going to change out the dvr tomorrow and see if it fixes the problem thanks for your help!

The original cable that is there is rg6 I ran a couple rg59 but I see the problem on a majority of the cams the distances are not that far also I have 2 power boxes...

I lowered it from 4k to 2k should I go lower? I dropped the resolutions from 1080 to 720 and the FPS from 15 to 13

Hello i have a DVR1604HD-L and i have installed all 16 HDSDI cameras to it everything works correctly but from time to time certain cameras would blink out for like 2 secs. I wonder is its the power so i went to buy a brand new power supply box each one of these cameras without IR take up 300mA with IR on it takes 900mA i have 2 power box one is 10A 9CH and the other is 18CH 11A the 10A is a off brand power box and the 11A is an ALtronix SAV1820. i dont think the power is the issue but i could be wrong... there are 6 cameras going into the 9CH box and 10 cameras going into the 18CH box... i calculated all the power ratios and its all correct. Now i wonder if its the compression of the DVR.. i dropped all the videos down to 720P @ 14fps and now i only get 2 cameras that blink... please help if you ever encountered this problem... thanks

Hello i have a DVR1604HD-L and i have installed all 16 HDSDI cameras to it everything works correctly but from time to time certain cameras would blink out for like 2 secs. I wonder is its the power so i went to buy a brand new power supply box each one of these cameras without IR take up 300mA with IR on it takes 900mA i have 2 power box one is 10A 9CH and the other is 18CH 11A the 10A is a off brand power box and the 11A is an ALtronix SAV1820. i dont think the power is the issue but i could be wrong... there are 6 cameras going into the 9CH box and 10 cameras going into the 18CH box... i calculated all the power ratios and its all correct. Now i wonder if its the compression of the DVR.. i dropped all the videos down to 720P @ 14fps and now i only get 2 cameras that blink... please help if you ever encountered this problem... thanks

Anyone?

I'm stumped.

Hello all

I know this problem is beat to death but I tried an alternative and I still have the problem, wonder if anyone can point me in the right direction.

I have 16 cams all ran from 50ft to 370ft (6 under 100ft/ 4 under 300ft / 2 under 370 ft) all the close ones seem to have power... 50-100 ft I understand that it could have been a power I originally have a psu that was 18ch 12V/10amps my cameras are 500mA each so

16cams x .5A = 8A total do I figure 10A will do the job.

It didn't. Only for the short runs now I have one that is borderline and it provides power but it have a gray screen flickers but that's about all. So my solution was go buy a new psu. Bout a 18ch 12A still all the same problems... I'm stumped like analog ill attach pics of what I am seeing.

hope someone can help me out thank you.

Still have it? Can you pm me some pictures? And prices

admin

admin

user

admin

admin

111111

admin

888888

hope one of those work! I been using all kinds of dvrs and usually 90% of the time thats the defualt!

goodluck pal

thanks!

if i use a router connected to the 2wire router will it help? helPpppp!

I have local access to the dvr... I can view it if I'm on the network... But I can't get 2wire router to see it when I need to port forward the dvr...

all i know is the best 16ch NVR dahua has can only support up to 4 channels 1080P...

hey guys any network gurus out there?

i have 2 dahua DVR1604HF-A i need to open 2 ports but the problem is on the 2WIRE router my client has it will not detect the dvr's how can i fix this problem?!

any help is much appreciated!

thanks all

If you live in Houston I'll install one for you!

so i concluded im building a hybriid dvr... any recommendations on parts guys? i want to house it in a micro atx chassis.. any input appreciated thanks!