radman

Yes it does all still working fine I just wish the recorded video was better quality

I think I have solved my problem I removed all the previous drivers and installed the v8.3 again this time it said upgrading hardware from 1.42 to 1.55 rebooted and now it has been running for 2 hours Sorry just noticed Tracker I am using a GV-1240 D type 16.

I downloaded 8.3 from Geovision they gave me the link after verifying my details, I installed it ran for about an hour then said my card may be counterfeit and duly shut down No way is this a dodgy card it has been running since 2007 on 8.1.2.0 and 8.2! I restarted the software and it has now been running for over an hour! I have reported the fault to Geovision it will be interesting to see what they say? It happened again so back to 8.2 until I get some info from Geovision

I received an email this morning saying it was released on the 2nd Feb! I have sent a reply so wait and see time

I have filled in the registration again James still no link to the download Sorted thanks James

I am leaning on the guys who know again My front driveway camera is constantly set off by headlights I can mask the road no problem but the lights shine on my drive I have the same problem in the morning with the sun and shadows anyone any suggestions

Back again !! I have bought a JVC TK-C1480BE which has RS485 set up inc digital zoom, is there anyway I can run the camera through the Geo software? there is a setup program I down loaded! if I am using Com3 for my GV-Net card I have no serial port on this new Intel board other wise I could use Com1 loads of USB's! is the answer to get another Gv-Net card? if I cant run it on the present setup Thanks, John.

Hi James thanks for the reply I did try Geovision but they just came back with a list the card will support not very helpful. The only solution I could think of was another GV-Net card and use Com1 or anyother apart from the one I am already using! then run the JVC software on it's own? Thanks, John.

No problem rory you learn one way or another I just appreciate the help and advice! John.

Back for more advice! on the card there is the video OP socket but pluging in a monitor there is no video, I have stuck a scope on it to make sure and there is none! Am I not doing something or am I loosing the plot

I tried again removing the software and folder plus the driver, re-installed the software and once again it came back with the old configurations. So I removed all again and went a bit deaper and there is a lot of files left in the windows folder I deleated them and reloaded the software and all is now well including DSP! Thanks to all for their help John.

Ok I uninstalled the software removed all I could find with RegCleaner reloaded the software it wasn't a clean install as the previous settings were reloaded password,cameras etc has this to be a total wipe of the Harddrive or is there information stored I can remove? Thanks, John.

Hi James I went from 7.05 GV-800 to the GV-1240 so I will give you suggestion a try, Thanks, John.

I am getting a bit confused the only reference to DSP I can find is when the Geo software is loading in the square box it says "Detecting DSP" then it disappears! where is Spot Monitor? as far a software goes rory I am running 8.12 and the card is legit and I have the latest DirectX 9 installed! "lost" Thanks, John.

Thanks matt I will investigate thanks for the info, John.

I got and understood all that Rory I will try a seperate Graphics card the on board is not bad but it uses the on board memory. The Iiyama is my PC monitor the cameras I am using are WV-CP484E and the results are good day and night I have a couple of dark spots which I will fill in with IR later. Thanks, John.

Rory or ? a similar question I get a realy sharp picture on a video monitor but when I view the same scene with the Geovision software it looks slighty defused/not as sharp! I am using a Iiyama 21" Pro 512 CRT monitor, the graphics is on board Intel G965 125mb the card is a GV-1240, is there normaly some degrogation? Do I need a better Graphics card? Thanks, John.

Hi all I got the Chinese Dome PTZ board talking to the Geovision software ok but what is the correct way to set up a zoom lens with a Panasonic WV-CP484E, I can get the lens to focus ok but I have to set up the ABF manualy is this correct? if I go auto ABF there is no way I can focus the lens! is there a correct procedure? Thanks, John.

Got a good result thanks to all for the help, John.

I will try all methods to see what works best but do I need to turn the lens sens to max? The Chinese PTZ board seems to work fine Rory I have a few spare switching functions! 4 relay and an Iris one must be able to do something with one of those?? Thanks, John.

Hi welding glass I have so that is good to open the iris fully do I turn the level pot to high? thanks, John.

Well Drunk or not I will give it a try thanks for the help, if in the sober light of day you can read your post and add anthing it will be appreciated John.

The answer is using the common connection on the control board join 5 and 4 together use 2 to the focus connection and 5 to the zoom the rest are not used unless you are using feedback to a telemetry monitoring system

I am trying to work out the wiring on a H6ZBME-5P Cosmicar/Pentax lens they are as follows:- 2 White---- 2 and 5 loosely shown linked like this [ 5 Blue ---- + 12v Near 4 Green ---- 4 and 6 loosely shown linked like this [ 6 Red ---- + 12v Tele 7 Orange ---- Pot Supply 8 Grey---- Pot Return 3 Sky Blue ----Wiper Focus 1 Pink ---- Wiper Zoom So I am assuming 2,5,4,6 and 7 are all 12v +ve and 8 is -ve Pins 3 and 1 go to the respective outputs from the control board It's a bit confusing if the above is correct why did they not connect 2,5,4,6 and 7 internally! or am I reading it incorrectly? Thanks, John.

I think it must be somthing to do with "Being Lost In The Translation" Rory