tomcctv

Hi no there is nothing you can change in the unit You are best buying a hybrid and not a TVT And also take into account .... You are wasting money going from D1 to 960h ..... Move to hybrid IP or start new all IP

Sorry but your calculations are wrong ........ Your using the lorex unit and that is 12v 5amp Are you using the POE from the unit ? Why are you bothered about power ???? Do you have a reason to get it low for 4 cameras

Look at it this way ...... TVT Make a DVR 960h but sell as a D1 recorder what would be the point Yes they have firmware but that alone is not going to turn your D1 into a 960 Board needs component changes also graphics .... HDMI output TVT can be had for $60 ......... You can't make it better

Hi. Yes we have the software for the Levi Where are you based

Hi. It depends if your using all your work as learning . I do understand what your trying to do but at each stage you will have problems Seeing your images ...... Yes you can take control of motors ....... Your next step would be to get the Data protocol stored on to your board Other problem looking at your boards ....... Your only moving low voltage motors ...... By the time you put everything together ...... Power will be your next problem ...... PTZ camera will always try and keep focus then zoom pan tilt ....... You need to take into account its full working power once camera is up and away from local power ........ Camera says 24v in spec

Don't think you are understanding ........they are PTZ modules So your not dealing with the PTZ side ?? Camera data is in head control

Hi. Don't understand what you mean about pin out From the light brown connector in your picture it is a basic ribbon connection back to the control in PTZ head

Admin Admin Is your login for PSS are you using that

Hi. No you can't make it a hybrid TVT is a budget system and just looking at a standard update you will find it will lock

Dahua ....... Shut down recorder for 20 minutes no longer that 30 minutes and retry

Hi. Might be best if you list the products you use As for your description above .... I would say look at avigilon

Hi . You do need to rest your router and again the IP address you are using is blocked so forget that as well You have also port forwarded your router ........ Bad thing to do I would start with a clean setting ....... And don't post your IP on open forum Find your external IP here http://whatismyipaddress.com PM it to me and I will check the ports for you

Hi. The DDNS IP you have listed belongs to Comcast and all ports are locked down I would start by doing a full reset on your router. Then I would start by using your external IP first before connecting to any DDNS service

Many have read your post ...... But to answer your questions right would mean typing for hours page after page glossary.php

Well good look ...... Just seen your other post $20 camera is not worth the extra money on switches Math just does not add up ...... Buying cheap then spending more to get it to work

Hi. Good old colossus installed 100s Problem is your recorder is 6 to 8 years old ..... Which is not a problem ..... But does not have smartphone viewer or support As far as a camera being down this could be as simple as been switched off from the system ...... Fuse gone in power Quick test is to move BNC connectors on back of unit around and see if it's camera or dvr channel Unplug all cameras and just plug 1 in at a time using only on channel

You have not listed your type of car but Lexus Jaguar Range Rover Toyota Dodge GM BMW All now have tracker .... CALL IT VEHICAL MONITORING ALL ABOVE have apps owners can use to monitor fuel service history or even a bulb out....... Open / lock / remote start Think removing your dash is a bit dramatic....... Just take car to your local dealer.

Hi ... Is your car old or new or company car You need to give history of car And also in some cases in the states a car on finance or lease may have tracker Or owner before you had tracker

Hi. Make a new file on USB and call it dvr ... Then move your firmware to that file

Hi. A home plug will not power your camera You need an injected or POE OR peer at camera LAN alone will not power your camera

LAN Power ???? Your first post is confusing ...... How are you powering your cameras ?

That is a bad site been talked about on here before Your system will now be open to that site when you connect your system to Internet Delete everything from that site off your PC

Hi. What will you be looking at with cameras ??? You seems to be worried about budget and doing cheap So from your post above ......... 96 cameras are not going to be cheap ..... So why install 96 cameras and not have them protect buy the system every day and night. Reduce the amount of cameras and budget more storage. Is you system for theft or vandalism or just to monitor an event

Can I ask which password and user name you have used

I'm in Swansea Hi do you remember the name of card or name on screen when it was working Your card might just need a reset