tomcctv

Hi. ljarrald the signal from the camera should not be changing the settings on your projector having monochrome comming up on the screen would not be comming from the camera. is your camera from the link you posted or is it that it looks the same. (the one you have listed is a qvis camera) and it has no monochome settings

just sales marketing some data sheets will give TVL as a colour camera some will list the best TVL but not tell you thats in B/W

Hi. you will be looking for a hybrid solution. take a look at aver NV3000 card http://www.averusa.com/surveillance/productdetail.aspx?id=100

Hi. vmgtlexi. looks like you are getting there. the problem now with your youtube video is common with the winner5 chip. if you have extra light comming into the frame. hence the pulsating. with you camera being in a small area the sens-up funcation is trying to alter the light. switch this function off in your camera settings you may need to turn your britness up to get the right image you need.

apart from the wavy lines ... now you have a good image (now the power is right) the best so far from all your posts. but i do wish you had gone for the power supplies that were recomended to you in the other post. as you can see from your new video (centre of screen) you can see it pulsing this is a sign of a unregulated power supply. which are not good for cctv

hi james i would find another supplier if i was you (well over priced ) £113 for a fixed lens camera (more like £29) DVR £290 ($500) for a avtech that must be a typo

hi is this your dvr ?

Hi. it should not matter which cameras you have attached to your dvr. for some reason qvis have desided to charge for there Apps so use the Free dahua App instead. just scan with your mobile.

hi KP is just a store ...... you could have any make of dvr or card that they sell under there own name. most of which are avtech. but you have a card (being pc based) you will need to post screen shots or image of card to see what make it is.

hi for 2 x 1.3mp just use a aver nano its cheaper than building something.

hi it does not matter polarity on 24 ac (if not marked) so just connect + - to any pin.

before going full 24v on your system are your existing cameras 24v ??? or duel voltage

How do you get that its much more powerful than the Nuvicos? This samsung camera is just a 2.8-10mm TDN IR bullet camera. Max. 6.8W (LED On) ops manual the manual i have here website spec sheet all say 4 amp max 12v ok lets forget the what the manual says. but 0.5 amp for a winner 5 36 IR camera is not right. far to low. so lets just say all your cameras are 1 amp thats your full 5 amp used nothing for IR switch on or filter move. you are still under powered Rory even calculators cant be that expensive to buy out there

are 1 amp each total 3 amp you say samsung is only 0.5 amp (much powerful camera than Nuvicos) how can it run on less ??? manual says samsung 4 amp ..... its this high because of power drew of IR kick in so lets do your sums again. 3x 1 amp (Nuvicos) 1 x (working samsung ) using the last 2 amp that you have left. but under powered as all your 90 post surgests. so thats 5 amp just on 4 cameras (under powered) and you want to add another HOW you have no power left. you need at least 10 amp for what you have.

so 5 cameras on power unit 5 amp total. 2 of which are samsung winner 5 IR cameras just for the samsung to kick in IR will need 1-2 amp which you dont have with 5 cameras connected to a 12v 5 amp power unit. you have 90 posts on how bad your samsung camera is. it cant work at its full level if under powered. you say your getting 0.5 amp at the camera PAGE 8 on your install manual tells you the power you need and its not 0.5 amp. your 5 amp power unit does not take into account your full cable run on every camera (in total)

hi it depends on what system you have /// camera make software used on pc. there are so many types of cameras out there that you need to give us a bit more info

dahua full D1 is a good priced unit for your customer dont see the point in going CIF

Hi. the old steel and plastic eb cant work with CMS but the SA will and does not matter what age. for the places you do have the EBs its only 4 cameras it may be best to exchange them for the aver £99 ip 1.3mp and have your SA record them. then everything will be controlled via the CMS. at 4 fps from each camera 10tb should be ok for a few months.

Hi you can with the avers in a number of ways 1 you can have the dvr dump all video to an external drive system before it re-writes but this can be expensive in drives. best way is with a CMS server 1 unit will store from all your units at 4 fps per camera (you need gold CMS for this) we have 4 holiday inn s recording on site and 3 months backup at head office (group office) Dowshu. what ever you do with these units is going to be expensive we look after 2 120 system you can add raid to Dowshu (do you have rack system) not delt with Dowshu direct for a while (no one seems to know which way the company is going at the moment) they are members of the forum but not been on for a while.

if you only have 2 samsungs that need 4 amp i would just buy two of these power supplies. and use your existing 9 way power supply for the rest of your cameras. regulated 12v 5 amp cctv supply. but if your cable runs are long then you will need to go 24v

it will shut down at any time being on 1 amp. you are under powered ..... PAGE 12 camera power 12v 4 amp http://www.samsungsecurity.co.uk/upload/products/SCO-2080R/download/20100317_0_SCO-2080R_ENG_100316.pdf we use these cameras they are high powered 4 amp is unusual but that is what the camera needs.

on your video. camera starts menu then with it being night as soon as your IR comes on OFF goes your camera. under powered.

two cameras i have here and on every SCO- 2080r manual it states PAGE 5 The recommended adaptor specification for SCO-2080RN is DC 12V/4A, AC 24V/2A over. Please check the standard power requirement before connecting the power. ( Recommend AC 24A/2A over adaptor for a long-distance.) 1 amp will not start that camera.

hi. 9 cameras total 5 amp will be your problem you need 4 amp just for the samsung your camera are under powered. The recommended adaptor specification for SCO-2080RN/P is DC 12V/4A, AC 24V/2A over. Please check the standard power requirement before connecting the power. ( Recommend AC 24A/2A over adaptor for a long-distance.) you may find that this is the problem you have had with your camera setup.