tomcctv

hi. the Leviathan. is a very good little unit what size do you have 4-8-12-16 ??? the system can be played via windows but depends on which software you have. in the top right corner does it say delta wave or ljd 2 or ljd 3 (under the moving world)

Hi. buy a seperate kit. if the monitor has a problem on the system you have posted then you have no recorder either.

they must make the American ones different then. they do rory. you cant buy the monalisa in the uk.

hi. never had a CNB as bad as that. BUT i would say it is a setup problem. you cant compare those two images as the lighting is not the same in both images. CNB you have the extra lighting infront of the camera and on the Mintron you have it behind the camera

with your budget give ebay a miss. (no warranty) and your friend will only have to buy twice. Aver nano 4 is in your budget along with some small 650 tvl sony effio-E cameras.

Hi bantham are you going to sell me your 9000 pro yet

and end up with a system that only does 6fps ... how does that blow away 30fps ? that would be six images which works out as 3fps (frame not field) or ips

to be honest your buying crap. this is the spec from one of the cameras you have listed . Dimensions: 65mm(H) Diameter: 92mm(bottom) 55mm(top) Power: 12V DC Color: Black Pickup device: 1/3'' Sony Super HAD Color CCD Image Sensor: Powerful 1/3'' Sony CCD color image sensor chip Picture Elements: PAL: 512(H) x582(V) NTSC:512(H) x492(V) System of Signal: PAL Electronic Shutter Control: ON/OFF Switch Electronic Shutter: (1/60)-1/100,000 (sec) White Balance: Auto tracking white balance S/N: More than 48 db Auto Iris Lens: VIDEO/DC Backlight Compensation: ON/OFF Switch Horizontal Resolution: 420 TV Lines Lens Mount: 3.6mm Lens Mount: C/CS Mount (C Mount adaptor option) Minimum Illumination: F1.2/1.0 Lux Video Output: BMC 1.0 vp- p 75Ohm SCANNING FREQUENCY: PAL: Horizontal: 15.7343KHZ Vertical: 50HZ NTSC: Horizontal: 15.625KHZ Vertical: 60HZ Operation Temperature: (-20)C-(50)C what is that all about THE CAMERA HAS NO WAY OF CHANGING THE SETTINGS.

Hi same unit as the old deltawave / dahua. there has been no support for I.E for a long time. you need software to view your system. if you have a VCR connected then recording is fine. you could look at a encoder fitted to the TV/ monitor out to just view your cameras over the internet.

your card is 2004 / 5 tech were talking to you about 2009 / 10 card hence the reason for your D1 problem. that because its not on the card SHE was giving you advice about. it sounds like you want your 2004 card to function like the 2010 card (that cant happen)

POOR Connie. what2be. when you talk to geo you need to give them as much info on your product as possable your talking about 1 card and Connie is talking about another. i dont think she went on her lunch break i think she got a headache.

Hi SDM. is this a job you have done or are you being asked to just install the cables. a contractor was caught out a while ago that i know. he was asked to install a 16 camera system in a corner store but was asked to put all cables and power in 1 weekend and the cameras the weekend after. after they installed the cables the guy cancelled the order. when he went in a few days later with a bill for work done the guy had bought a cheap system from ebay. he only used him to fit the cables to make it easier for him to install his own. and wanted a discount if they are asking for you to just install the cables charge full hour rate and full price for cable BNCs and Power.

Motion trigger.

Hi. we do alot of hotels cctv wise. so we see alot of AC controls. PIR and the likes can Treble the hotels electric bills. it is cheaper to leave an AC running than stop and start (it uses alot of power just starting up) so if it does not detect all the time the cost can go up. there is a themostat for hotels were you take the room key card and insert it into the room stat (this is not a card reader) it just turns on the system via micro switch. entre room insert keycard AC on when they need to leave the room they need there card key so switches everything off.

hi. sorry for delay (time zone thing) filters in pic are Numatics filters used for filtering oil. so you will have no problem getting airflow can be bought as picture or in flat sheets. should be able to get from you local numatics pump supplier or a good truck garage.

were did the unit come from off ebay was it uk or france ??? i can flash it for you ( your cost P&P) but first can you post a picture of your unit.

Hi. you can buy this in lenths just push between the 2 shrouds.

hi the eco is no longer made. your dvr is the new LED D1. if they said it will work then you will have no problem sending it back under warranty. the dvr has to go back to be flashed

hi. the LED does not have a firmware update its only been out for 2-months were did you get the firmware from ??

Hi. if you have used 2.606.AD firmware then that is not for your dvr. its for the old eco. the dvr you have is new so no update firmware yet. you will have to send your unit back

hi. you are controlling the cameras from your dvr software which is fine but on your diagram you still have the 485 connecting both (you cant) your diagram shows DVR 1 controlling 1 camera .... DVR 2 controlling 5 cameras and with the 485 link back to DVR 1 from DVR 2 why do you need this ???

Hi is this your DVR ??? there are 2 apollo led 1 is qvis and another is a cheap chines DVR.

Hi. FlameOut. no such thing as a dumb question. its good to do your homework first. the link you have posted are avtech DVRs. you can do better than that. the other problem with the likes of the systems from sams is the cables cheap and not much good for cameras. so i would look at buying seperate bits of equipment i.e DVR / cameras / power unit. and buy a reel or RG59 with power. you cant go wrong with a 4 way dahua DVR and pick cameras for your surroundings internal or external.

hi. CNB box cameras are a good price. ZBN-20Z18/ZBN-21Z18

hi. you would still not get control from another dvr. DVR 1 you set up your settings for control of the camera... so as when you click on the camera you can use the onboad controller to zoom. so if you then move to DVR 2 and you want to control the same camera you cant it is not in the DVR settings. 485 is out only (transmit) so you have 2 DVRs and 2 monitors. you can do it with the mace but you would need to go 2 DVRs to PC with monitor and use mace CMS.