tomcctv

Hi everything is in the box …… I unit plugs into a socket by your recorder you then plug the Ethernet into dvr then the plug

you use the other plug by your router and connect the Ethernet cable into router then plug….. all leads are supplied

Hi best and simple way is a tp-link set they are cheap and plug and play job done in 5 minutes 

https://www.tp-link.com/uk/home-networking/powerline/tl-pa717-kit/

9 hours ago, viralfolks said:

It's important to seek permission from the relevant authorities and the construction company before installing  cctv monitoring services on the site, and to ensure that the cameras are placed in a safe and secure location.

WHY ???? ….. no wonder you need to spam giving advice like this to your customers 

nothing to do with monitoring…… post is 12 years old

40 minutes ago, benbenlol said:

I also plan to congratulate my father, but I'm still not sure what a gift to give him. Do you have ideas?

Socks are always good or PJs

So secondhand hard drive WD…… you still have not said what type or speed or even age

you don’t get any good results from online HD tools …. Infact they don’t even delete the old data on them…… so may still have bad sectors 

Hi ….. no you won’t have problems switching rs485 around as it’s only data not power

just for a quick test remove the 485 from keyboard and connect to dvr and see if you have control then

So it was a secondhand hard drive ?

what make of drive and type is it

drives should be formatted on the unit there going to be used on .. not pc

Ok what size hard drive did you replace it with and type ….. and was in new and formatted by the recorder

Hi. Skipping on video playback is motion sensitivity is set too low and also your pre and post settings…….. you could also have bad sectors on your hard drive

Hi. The problem you have explained has nothing to do with firmware

you system can’t be working for years and then just stop working this points to a component fail something like hard drive 

firmware can’t fix components 

hacked or hard drive problems 

with you having the XMEYE it is not worth spending time on

app stopped support 2 years ago it’s also China P2P ….. this is why you get adverts on the app before you can view your system

1 hour ago, dazza 2023 said:

Is there an update for this model????

HI ….. no updates ……it’s a cif recorder so updated software would not run as the unit would not have supported hardware 

13 hours ago, ggsmit said:

i need to add two existing analog cameras to the mix. can i use passive video/power/audio baluns at the camera ends to feed power and data via cat5 to them and will i be able to view their video/audio as per the other 8 ip cameras?

Hi …. No …. Not unless your nvr is hybrid 

you can’t directly add analog to iP system not with baluns

wifi camera to nvr ……. Wi-Fi cameras people get mixed up with cctv vs smart cameras…. Most smart cameras won’t allow nvr connection as there registered to a server (China)

Hi. This will just be a setup problem 

with your ptz cameras view on the screen power them down wait 2mins then back on first thing they will do is go into setup mode ….. you will see your camera moving to set points …. But while it’s doing this you will also see the camera settings on the screen 

address -protocol-baud rate 

then in dvr ptz setup match those settings to the camera …….. 

On 2/28/2023 at 11:15 AM, BobPlayAnything said:

I was thinking on adding a poe ip camera that have a built in microphone so i can monitor sound and video from the dressing room with a pc

Do you not see the problem in doing this ?

CD key … 93xxxxxxxxxxxx

remember all case sensitive 

also have lots of parts for avermedia

Ok so what is the 12v for 150m is still too long 

what amp is drawn

and what connectors are you using BNC to scart or RCA

Hi 920ft is a big distance to run monitor over without a signal booster

what connection is at monitor end and dvr end

also why having 12v ? Over that distance you will be lucky to have 6v

Hi yes it is very possible which country are you in and is Vodafone available ?

Hi now you have shown the screen yes it’s a dahua nvr6000

and no sync can also mean out of range are you using the remote app ? Also what monitor are you using and connection type vga or hdmi 

monitor type is a problem with some early dahua units ….. if the monitor settings are changed then video goes out of range and you will need a HD tv plugged in to lower the range 

but yes it’s worth getting working …… I go past your area every few weeks but I think we can get you back up and running without a visit

6 hours ago, steven@segers.ph said:

The most obvious possible cause would be that both devices are broken, but this seems unlikely since they were both still new in packaging.

Hi both you auction units are old …. Bosh is 7 years old dahua is 9 years old and both units are analog 960h only 

your zosi is a HD analog TVI unit and can only use TVI cameras …… if you just need a new dvr look for a 4 in 1 unit …. This will allow you to use your existing cameras 

Hi … yes by your photos it is 100% a dahua 128 channel nvr 

the plug in the centre top is there as dahua badge removed

what does the system do if anything ?

and we’re are you based 

how many cameras do you have 

That is 100% a dahua 128 …… Ic always used dahua even the apps are rebadged dahua 

also I used to deal with Ic for years till they went into liquidation in 2016

how long have you had the recorder the storm is a 8mp so it can only be a year or so old ???????? 
 

I think yours is 8 years old 

Hi. It’s not worth it to pay for old systems to work 

Ic used dahua units …. Which yours is

its sounds like the units software has gone corrupt 

With age of unit installing newer software would not work as hardware is too old

Hi. I would say get a new camera and not the xmeye 

your pictures show connection to China server for password reset ????

asking for phone number and twitter account for setup then it’s time to put in the bin

yours is old so replace would be better and more secure

4 hours ago, GiovanniG11 said:

When It was connected to the PoE switch, which unfortunatly I don't have here, the PoE led was on, half seconf after connecting cable, but the link was off, this is not normal.

Or you could of simply just used the cameras software

if it has been used before you have no clue on cameras iP range …… then you have password problems….. just connecting to pc does not mean it’s done

POE ….. indicator lights will show with data and power …….. no data path ( wrong IP) lights go out