crow

do i need to 12v power the cameras that i need to log onto?

as they are all fitted and out of reach to power them for quick fix

went there today and unpluged all cameras and group deleted the info in the config menu in the nvr

then i pluged in 1 working camera at a time

this is the first 2 cameras info only one pluged in at a time then deleted the info after i unpluged it

then the 4 working cameras all in at once then this is the screen info with just 4 working cameras in

ive not had much to do with poe cameras and nvr's just tvi with coax

dont know whats going on

is there any way i can reset the cameras without powering them and takeing them down?

thanks

hi

thanks for the info

yes all same manufacture sannce

the router is about 10 foot away from the nvr

i have a long ethernet cable but no adaptor to connect the camera's ethernet cable to the long ethernet cable i have

i will try to get one tomorrow

thanks

hi

the lan 1 is 192.168.1.?

and the lan 2 is 192.168.2.?

hi a friend has got the sannce N48PT with 8 sannce poe cameras

4 are working ok but 4 say net error or blank

someone has been into the nvr menu and changed some of the cameras ip address

the ones that are working have status green dot , ip/domain cameras mac address in this part

port 8000, protocol type1

the 4 that dont work have 192.168.2.22 , port 80, or 8000, type onvif

how do i get the cameras working again or reset them to how they were

i tryed to connect my laptop to the nvr by changing the laptops ip to match lan 2 on the nvr

but couldnt get any config tool to work

cheers

hi

you cant just use a splitter for cctv

you need an rf modulator

I had to use one to get cctv into a few TV's

just search rf modulator in google

i had same with a qvis one

hard drive was bad

anyone used these and are they any good

http://www.biz4security.com/news/detail-221-hikvision-launches-new-600tvl-dis-analog-cameras.html

i usualy use qvis bullet p400 efio e cameras

cheers

Hi

One of my pelco spectra 3 cameras has started playing up

If I move the camera with the joystick or through the network

I get a full screen of numbers with degrees next to them

And if I zoom in or out I get a full screen of the rectangle bars you usually get 1 when you zoom not a full screen full of them

The camera still has a picture under all the numbers/rectangle bars

If I go into the cameras menu and then exit

the numbers are gone until I move the camera again then the screen fills up with the same crap

Any ideas has it had it

Cheers

just set up a new account with no-ip

https://www.noip.com/sign-up

you get 3 free accounts

and choose the no-ip option on the dvr

hi

port forward ports 80 and 34567 and 34599 only

on your router to the dvr's ip adress which is 192.168.0.10

then double click where it says members.Dyndns.org on the dvr (your photo 2 in your post)

and it will open up to choose the ddns settings which is where you will input you ddns account name and password

this will get you going

also if you try to log onto your cameras from where the dvr is (LAN) you might have to put the dvr's ip address into the ipad iphone pss on the pc software

instead of the dydns name and just use the dydns when your away from the dvd (WAN)

great thanks for your reply

thats why some work and most dont

Hi

Why is it that on most of my dvr network setups using a ddns account name

I can't logo to the dvr localy

I have to use the DVDs IP address instead of the ddns name

But I can log onto the dvr with the ddns name from the wan

Thanks

HI my friend has one of these dd427-x and another has the dd423-x pelco ptz cameras

the 27x one lights up very dark areas automaticly and the 23x one doesnt ,they are both running default factory settings

has the 27x one got some kind of chip that does some kind of fancy lightening trick?

cheers

Got it working now

It was set to std coaxitron ,when I changed it to extended coaxitron it worked on the patterns

Dip switch 2 switches were all off apart from 5 and 7

Not sure why as I put them all to off and it works ok

Any one know what they should be set to

Cheers

got it all up and running in a fashion

but cant run the pattern from the joypad

any one know how to work these

cant make the instructions out

thanks

hi

ive just got one of these

dont know anything about matrix's

all i have used before is a keyboard controller with digita display to set the board rate e.c.t connected with the rs485 twisted pair

i have 2 pelco spectra 4's cameras to try out with the matrix and a keyboard joypad

the matrix is a pelco cm6700 and the joypad is a kbd300a

the keyboard is conected to the matrix in local keyboard socket and thats all thats connected at the moment

how would i wire it up to test the 2 ptz camaras and the matrix / joypad

and what would the dip switches need to be set to on the ptz's

thanks for any help

thanks for your replys

yes must be the upscaling as its a 50 inch hd plasma with a high res

a lot higher than 640x480

thanks for clearing that up

hi

when i use the bnc output from the dvr to a phono adaptor to a tv's phono socket its always slightly blurry

is this always the case

thanks

hi

my mate has on of these ptz cameras

and it keeps going blurry, the automatic focus stops working and also the manual focus stops too

if i do a reset to factory settings or a reeboot or cycle it will work fine for about 20 mins then go blury again

any ideas whats wrong with it

cheers

hi

i had this exact same problem with a pelco ptz

it did the same in the menu just kept rolling over and over untill i gave a flick in the opposite direction

and all i did was set the dip switches all to off and just the address to 1 and this made it ok

worth a try

Hi

Does anyone know where to get a wall bracket from in the uk for a pelco spectra 4 27x ptz the one that attaches to the camera housing with threads in

And do the smaller zoom and larger 35x ones fit the 27x

thanks

Just tried my mates spectra 4 in my housing and it has been running a pattern all day with no problems

So it looks like my spectra3 has dome has a problem

HI

a friend has just got one of these ptz cameras

im going to help him fit it

it says network camera (what does this mean and what can it do)

we have never had a network camera as we just conect the dvr to the net and do remote viewing

also what settings do the dip switches need to be on

he has only 1 ptz so i put switch 1 number 1 onto on for address 1

but not sure what the other switch 2 should be at

we are using coax for video and 1 twisted pair for rs485 conected to the dvr

thanks

The qvis shotgun cable has got some shielding in the centre

And this is made for cctv

Is there a difference with the qvis cable

Cheers