crow
-
Content Count
140 -
Joined
-
Last visited
Posts posted by crow
-
-
hi
thanks for the info
yes all same manufacture sannce
the router is about 10 foot away from the nvr
i have a long ethernet cable but no adaptor to connect the camera's ethernet cable to the long ethernet cable i have
i will try to get one tomorrow
thanks
-
hi
the lan 1 is 192.168.1.?
and the lan 2 is 192.168.2.?
-
hi a friend has got the sannce N48PT with 8 sannce poe cameras
4 are working ok but 4 say net error or blank
someone has been into the nvr menu and changed some of the cameras ip address
the ones that are working have status green dot , ip/domain cameras mac address in this part
port 8000, protocol type1
the 4 that dont work have 192.168.2.22 , port 80, or 8000, type onvif
how do i get the cameras working again or reset them to how they were
i tryed to connect my laptop to the nvr by changing the laptops ip to match lan 2 on the nvr
but couldnt get any config tool to work
cheers
-
hi
you cant just use a splitter for cctv
you need an rf modulator
I had to use one to get cctv into a few TV's
just search rf modulator in google
-
i had same with a qvis one
hard drive was bad
-
anyone used these and are they any good
http://www.biz4security.com/news/detail-221-hikvision-launches-new-600tvl-dis-analog-cameras.html
i usualy use qvis bullet p400 efio e cameras
cheers
-
Hi
One of my pelco spectra 3 cameras has started playing up
If I move the camera with the joystick or through the network
I get a full screen of numbers with degrees next to them
And if I zoom in or out I get a full screen of the rectangle bars you usually get 1 when you zoom not a full screen full of them
The camera still has a picture under all the numbers/rectangle bars
If I go into the cameras menu and then exit
the numbers are gone until I move the camera again then the screen fills up with the same crap
Any ideas has it had it
Cheers
-
just set up a new account with no-ip
you get 3 free accounts
and choose the no-ip option on the dvr
-
hi
port forward ports 80 and 34567 and 34599 only
on your router to the dvr's ip adress which is 192.168.0.10
then double click where it says members.Dyndns.org on the dvr (your photo 2 in your post)
and it will open up to choose the ddns settings which is where you will input you ddns account name and password
this will get you going
also if you try to log onto your cameras from where the dvr is (LAN) you might have to put the dvr's ip address into the ipad iphone pss on the pc software
instead of the dydns name and just use the dydns when your away from the dvd (WAN)
-
great thanks for your reply
thats why some work and most dont
-
Hi
Why is it that on most of my dvr network setups using a ddns account name
I can't logo to the dvr localy
I have to use the DVDs IP address instead of the ddns name
But I can log onto the dvr with the ddns name from the wan
Thanks
-
-
HI my friend has one of these dd427-x and another has the dd423-x pelco ptz cameras
the 27x one lights up very dark areas automaticly and the 23x one doesnt ,they are both running default factory settings
has the 27x one got some kind of chip that does some kind of fancy lightening trick?
cheers
-
Got it working now
It was set to std coaxitron ,when I changed it to extended coaxitron it worked on the patterns
Dip switch 2 switches were all off apart from 5 and 7
Not sure why as I put them all to off and it works ok
Any one know what they should be set to
Cheers
-
got it all up and running in a fashion
but cant run the pattern from the joypad
any one know how to work these
cant make the instructions out
thanks
-
hi
ive just got one of these
dont know anything about matrix's
all i have used before is a keyboard controller with digita display to set the board rate e.c.t connected with the rs485 twisted pair
i have 2 pelco spectra 4's cameras to try out with the matrix and a keyboard joypad
the matrix is a pelco cm6700 and the joypad is a kbd300a
the keyboard is conected to the matrix in local keyboard socket and thats all thats connected at the moment
how would i wire it up to test the 2 ptz camaras and the matrix / joypad
and what would the dip switches need to be set to on the ptz's
thanks for any help
-
thanks for your replys
yes must be the upscaling as its a 50 inch hd plasma with a high res
a lot higher than 640x480
thanks for clearing that up
-
hi
when i use the bnc output from the dvr to a phono adaptor to a tv's phono socket its always slightly blurry
is this always the case
thanks
-
hi
my mate has on of these ptz cameras
and it keeps going blurry, the automatic focus stops working and also the manual focus stops too
if i do a reset to factory settings or a reeboot or cycle it will work fine for about 20 mins then go blury again
any ideas whats wrong with it
cheers
-
hi
i had this exact same problem with a pelco ptz
it did the same in the menu just kept rolling over and over untill i gave a flick in the opposite direction
and all i did was set the dip switches all to off and just the address to 1 and this made it ok
worth a try
-
Hi
Does anyone know where to get a wall bracket from in the uk for a pelco spectra 4 27x ptz the one that attaches to the camera housing with threads in
And do the smaller zoom and larger 35x ones fit the 27x
thanks
-
Just tried my mates spectra 4 in my housing and it has been running a pattern all day with no problems
So it looks like my spectra3 has dome has a problem
-
HI
a friend has just got one of these ptz cameras
im going to help him fit it
it says network camera (what does this mean and what can it do)
we have never had a network camera as we just conect the dvr to the net and do remote viewing
also what settings do the dip switches need to be on
he has only 1 ptz so i put switch 1 number 1 onto on for address 1
but not sure what the other switch 2 should be at
we are using coax for video and 1 twisted pair for rs485 conected to the dvr
thanks
-
The qvis shotgun cable has got some shielding in the centre
And this is made for cctv
Is there a difference with the qvis cable
Cheers
sannce N48PT nvr poe camera reset p address
in Installation Help and Accessories
Posted
do i need to 12v power the cameras that i need to log onto?
as they are all fitted and out of reach to power them for quick fix
went there today and unpluged all cameras and group deleted the info in the config menu in the nvr
then i pluged in 1 working camera at a time
this is the first 2 cameras info only one pluged in at a time then deleted the info after i unpluged it
then the 4 working cameras all in at once then this is the screen info with just 4 working cameras in
ive not had much to do with poe cameras and nvr's just tvi with coax
dont know whats going on
is there any way i can reset the cameras without powering them and takeing them down?
thanks