Jump to content

crow

Members
 View Profile  See their activity

  • Content Count

    140

  • Joined

  • Last visited

Posts posted by crow

  1. Posted

    Hi

    Yes there is a fan and heater

    My camera is 24vac not 12 v

    Can I run 12 v dc on it

    also can the fan and heater be turned off.

     

    I had it running a pattern tonight and it didn't go for an hour

    It got stuck to the right and went 1 inch to the left and back again to the right over and over then after a while it went up in the air again going very slowly to the left in some kind of its own pattern

    When I moved the joystick it wouldn't go up any more as it was at the end of travel

    So I moved down and it did a 180 spin then it would move up again

    I have set another pattern tonight just left and right stopping at

    intervals without using the zoom and its running ok

    It will run for constant on a scan left to right without problems

    And has been doing so for months

    It's only when I do a pattern with zoom in it that it losers the pattern

    Anything els to try

    Thsnks

  2. Posted

    hi

    i have a pelco spectra 3 ptz camera

    when i set up a pattern it sometimes goes off the pattern i set

    i can set it up and then after a few hours or a couple of days it will be pointing up in the air stil doing the pattern but up into space

    i stripped the camera down but there is no damage to the motor plastics or the mecanism

    my power supply is only 2 amp is this enough?

    thanks

  4. Posted · Edited by Guest

    can you post a picture of the front..... it looks like an old hikvision.

     

    also if it works (looks like its been at the bottom of a pond with all the rust on the connectors)

     

    see if it has PTZ controls on the software. delta wave (hik) does not

    hi mate

    its dust not rust

    it has the ptz software and its definatly an adata apollo lite dvr

    cheers

  10. Posted

    hi thanks again for the reply

     

    i have used qvis ptz cameras before and to access the menu you pressed preset then 95 and then you could use the joypad to scroll through the menues and even move joypad to the right to enter the sub menu

    with my pelco spectra you can move the joypad up or down in the menu but cant move to the right to get into that particular menu,you have to press open

    im getting used to it now

     

    i managed to get the camera to stop at the left and right limit with scan limit stops

    but im not sure if zones is a smooth scan from left and right like the qvis ptz i have used

     

    the pelco seems to ramdomly stop inbetween the left and right limit

    instead of a smooth left and right continuas movement

     

    i set a patteren up as this is same as the qvis

    i just need to find out how to get the camera to go from 1 stored preset to the other preset now

     

    thanks for all your help

  12. Posted

    hi ive got a couple of these cameras and have a few questions adout the one that is ok

    first my keyboard controller is one of these

     

    http://www.adata.co.uk/Catalogue/ANALOG-CAMERAS/PROFESSIONAL-CAMERAS/PTZ-CAMERAS/PTZ-ACCESSORIES/Black-Keyboard-Controller-for-G3-PTZs-G3LITEKEYBOARD-SF

     

    and there is slight differences to get into the camera menu e.c.t

    pelco instructions say press 95 then preset

    i have to press set then 95 then preset

    also lots of other diferences when in the settings,not sure what i can do about this

     

    also when i try to programe a scan (zones)from left to right pan

    i set the left and then set the right

    when i run the scan it doesnt go to the left fully that i programed and then will go to the right i programed ,then will go round to the right again (onto my house bricks)to my left limit i programed

     

    am i doing somthing wrong

    is the (zones) left and right suposed to pan fron left to right

    hope you can understand its kind of hard to explain

     

    cheers

    1619572d-06f3-48c6-b5e0-9fde011b1b43_210x210.jpg.b2dcea333d92e55e042f2c2b453b95f9.jpg

  17. Posted

    hi mate

    thanks for the quick reply

    i also noticed the camera wasnt centered as though it had come away at one end

    ill give it another go at opening it up

     

    when i get the belt back on does it matter that the camera isnt in the same position where it was when the belt came off

    so it wont bind and go behond the limits? e.c.t

    if you get what i mean

     

    say if it is at full upward travel then the belt comes off and then i put it back on and the camera is at the bottom of travel

    wont it bind when the camera goes to the bottom

     

    or doesnt it matter

    cheers

×