catseyenu

Email of events with pic attached from 2032 cam was working. Email settings did not change. Events email from NVR & IVMS 4200 with same email config. works but they don't seem to see or trigger on the camera's extra intrusion features (virtual plane traversal, & intrusion detection in particular). I've enabled the 2032 debugging, using commands: # setDebug -m EMAIL -l 6 -d 111 # outputOpen Test from camera: [07-17 11:28:04][OTHER][ERROR]The str_ipv4(smtp.gmail.com) form not accord with IPv4! connect server_name=smtp.gmail.com, port=465 SSL init SSL connect init_mail_sender hello login received not expected response. received=250-SIZE 35882577 login: Server authentication error initial mail sender failed, ret=-18 SSL free Opened IVMS-4200, control panel, remote config of NVR, test email and get success. Still using IVMS-4200, remote config of camera, test email and get success. Back to browser, test camera email... success! Test again failure. Debug output: [07-17 13:27:31][OTHER][ERROR]The str_ipv4(smtp.gmail.com) form not accord with IPv4! connect server_name=smtp.gmail.com, port=465 SSL init SSL connect init_mail_sender hello login sendHeader sendContent sendEnd fini_mail_sender quit close fd: 66 ssl shutdown SSL free [07-17 13:30:24][OTHER][ERROR] checkUserIdValid is ERROR [07-17 13:30:24][SYSLOG][ERROR]Invalid userID 1513388852 [07-17 13:30:24][CAPA][ERROR]get_alarm_capability CAPATYPE_NOT_SUPPORT [07-17 13:30:24][SDKCMD][ERROR]CAPATYPE_NOT_SUPPORT, capabilityType = 10 [07-17 13:33:03][OTHER][ERROR]The str_ipv4(smtp.gmail.com) form not accord with IPv4! connect server_name=smtp.gmail.com, port=465 SSL init SSL connect init_mail_sender hello login received not expected response. received=250-SIZE 35882577 login: Server authentication error initial mail sender failed, ret=-18 SSL free Anyone see anything that I'm missing or have any suggestions?

Looking at the NVR Network Config... turned off DHCP & assigned the NVR an IP on my local LAN (192.168.1.10) and rebooted the NVR. It shows the Internal NIC IP4 Address as being on a different subnet (192.168.254-1). Do I need to assign the internal NIC the same IP (192.168.1.10)? The NVR is assigning the POE connected camera's an IP on the same 192.168.254-* subnet? Turning DHCP off doesn't turn it off?

While there may be many ways to skin a cat this certainly qualifies as one of them. " title="Applause" />

FTP was removed in 5.20, you would need to down grade to a prior version using TFTP. Your best bet may be to contact CBX.

TFTP Automatic Update Tool User Manual http://www.hikvision.com/europe/support_more.asp?id=269

A couple of WAGs that may be totally useless... You may want to try to get the debug output from an email module. Also check your network settings in the DVR, i.e. not having DNS set up has been noted in other posts on email failure.

Is there a reason you have not used SADP to check the IP? It is located on the disc that comes with the camera as well as online here: download/file.php?id=6715

What IP are you pinging from? Does SADP see the camera?

Bingo, thanks! Under Events I get the motion blocks as well as the line traversal showing but under Live View all I see is line traversal? The question of why this isn't ported to the NVR's display also comes to mind.

+1 IIRC it seems like I've seen the green indicators under normal mode but not expert. Just another Hikvision programming inconsistency... I keep telling myself these cameras are good for what they do, I'm just not always sure what it is they do.

Because it's non-conductive?

Had a thought.. where is the TFTP folder stored? IIRC I had issues with having the working folder too deep (too many characters?) in my file system (ex.: C:\Documents and Settings\User\My Documents\Sec_Cam\TFTP\tftpserv). Try putting the TFTP folder in your root (ex. C:\TFTP).

Whoops, you are correct it did not complete.

iTuneDVR, thank you. I would assume it's not your host that is the problem. Thanks again!

Try creating a share under the Storage/NAS tab & then initialize it under Storage/Storage Management. Have you read through your manual that is on the included disc?

It must be my worthless ISP, AT&T's routing. They're only good for spying on us. /Looking for the middle finger emoticon...

The source file could not be read.

You have "Enable Event-Triggered Snapshot" checked under Storage/Snapshot?

Try checking off "Trigger Channel". /WAG

Connection timed out.

TFTP should work on Chinese camera with US firmware to overcome region mismatch. Your attached pic shows a successful TFTP install... I am confused.

Under the free tools tab. http://aliendvr.com/support/tools/

Try e4XCJ8 & vQuUh5

Use the SADP utility on the disc that should be included with the camera.

You've got to be kidding? Edit: It is, did you contact them?