Jump to content
fullmonty

Newbie Need A little Help

Recommended Posts

Hello Forum,

this is my 1st post I hope someone could answer my problem.. here we go

I would like to buy a ip speed dome cam for outside use, the one a have seen as 3 leads power / bnc / 2 wires

what I would like to do is use a RJ45 cable from the bnc to put into my router or do I need a dvr or nvr to plug in the back so recored and view on my iPhone

any help would be great

Nic

Share this post


Link to post
Share on other sites

take a few lead fishing weights and put them in a large tablespoon, then take a BNC cable (or RCA), then what you say..... another RJ45. Melt the lead weights in the spoon and then (*important*), while still molten, shove the BNC/RJ45/RJ45 splitter into the molten lead. Blow on it a bit to cool, and then plug in your equipment to make sure everything works as expected.

 

 

>>>>just kidding. If you go analog you'll need 1 pair for power, one pair for video, and one pair for the RS485 (ptz) data. Sounds like you have 7 conductors - give it a shot and let us know how it works. I'm just getting into POE, which it sounds like you're playing with, and I don't know the rules to that yet.

Share this post


Link to post
Share on other sites

Ok, just to clarify things an RJ-45 is a connector that looks like this:

 

248018_1.jpg

 

The cable you are referring to is probably eitehr CAT-5, CAT-5E or CAT-6. You can read the stamped writing on the cable to determine that.

 

The easiest way to use CAT5/6 wire with an analog camera is thru a pair of baluns which have a lot of different styles to them. Some provide power and some do not, you absolutely need one that does provide power. In general they will look something like this:

 

248018_2.jpg

 

248018_3.jpg

 

248018_4.jpg

Share this post


Link to post
Share on other sites

That's great so would this work on any ptz I'm thinking about getting this one. As you can see the connections also the spec

So I need a video Power & Video CAT5/6 Video Balun then I can plug into a drv or nas then into my router,?

I hope iv got that right and is a good ptz camera to buy

 

 

Effective Pixels 976X582

Lens 12X Optical Zoom (5~60mm)

Focal 5mm to 60mm

Min.Object Distance 10mm~1000mm (wide~tele)

Minimum Illumination 0.2Lux/F1.6(color); 0.02Lux/F1.6(B/W)

Electronic Shutter PAL:1/1~1/30000s

Day/Night Auto (ICR) / Color B/W

ATR YES

Backlight OFF/ON/BLC/HLC

2D-NR OFF/ON (Y/C level)

S/N RATIO >65db (AGC Off)

Analog Video Output BNC(1.0Vp-p / 75_), PAL / NTSC

Video

Video Output 1ch BNC

Resolution 700TVL Sony Effio-E

Frame Rate PAL: 25fps, NTSC: 30fps

Dome Drive

Pan/Tilt Range Horizontal: 0°~360° endless, Vertical: 0°~90°

Manual Control Speed Horizontal: 0.1°~80°/s, Vertical: 0.1°~80°/s

Preset Speed Horizontal: 80°/s, Vertical: 80°/s

Preset 16

PTZ Mode YES

Speed Setup Human-oriented focal Length/ speed adaptation

Info Display Time, Location, Dome title, Dome coordinates, Alarm, and etc.

Power Up Action Auto restore to previous PTZ and lens status after power failure

Idle Motion Activate preset/scan/tour/ patter if there is no command in the speci_ed period.

Time Task Auto activation of Preset by preset-time

Alarm Preset/Pattern output

Protocol RS485, Pelco-P/D, Auto recognition of general protocols

General

Power Supply AC 12V/1A(±10%)

Material Plastic

Power Consumption 10W

Working Humidity <90%

Protection Level IP66

Option ___ Wall & Ceiling Support

Dimension ___ ф138(mm) x 266(mm)

Weight 700g

Thanks for your help

image.jpg.aba262fbf97ab7de1c73c18f3faa8441.jpg

image.jpg.913942994c76d66bf35cb602e53916a6.jpg

Share this post


Link to post
Share on other sites

That is not a "ip speed dome cam" like you said on the first post, it is an analog camera.

 

It would work, but you would also need a DVR. You will not be connecting the camera to your router; but the camera to the DVR, and then the DVR to the router. When you watch the camera from your iPhone, you won't be connecting to the camera, but to the DVR. When you move the camera, you won't be sending commands to the camera, but to the DVR, which will then send them to the analog camera (through the RS485 interface).

Share this post


Link to post
Share on other sites

thank you for getting back in touch, yes I just notice the BNC and not the RG45 connector,

are IP cam Better then Analog?

and what you someone like to recommend me iv got €185 / £150 / $252

thanks

Nic

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×