Jump to content

Search the Community

Showing results for tags 'network'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type

IP Camera Forums

  • Welcome
    • Introductions
  • IP Systems
    • IP/Megapixel Cameras and Software Solutions
    • HD Analog
  • Digital Video Systems
    • General Digital Discussion
    • DVR Cards and Software - PC Based Systems
    • Computers/Networking
    • Digital Video Recorders
    • Dashcams - Mobile DVR's
  • Video Surveillance Systems
    • System Design
    • Security Cameras
    • Installation Help and Accessories
    • Video Transmission/Control Devices
  • Analog Video Systems
    • General Analog CCTV Discussion
  • Access Control Systems
    • General Access Control Discussion
  • Other Forums
    • Test Bench
    • Questions about this site
    • Trade Shows & Conferences
    • Classifieds


There are no results to display.

There are no results to display.

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start








Found 3 results

  1. I have a Hikvision DS-7616NI-E2 / 16P with 3.4.96 build 171128 firmware. I am trying to add another camera but keep getting a Network Unreachable error on the NVR and in iVMS-4200 it is error 1602. "Camera is disabled or not connected. Error code iVMS-4200.Video.C.exe[1602].)" I have tried multiple configurations within the NVR and iVMS neither method provides any promising results. If I go to the camera IP, I can see the stream just fine. It just wont connect to the NVR like I need it to. I have 10 functional cameras running but have 3 more to get connected which is proving to be a total pain in the r45 jack. Anyone have any guides or info they can send this way to help me get these things running? The camera I am working with right now is a HES328-TD-2.8.
  2. Hi all. I have come here for help. I installed an 8 camera Lorex (Costco) system in my own home. The CAT6 cabling was hung prior to sheet rock in our new build home by the builder's sub. Visually, it looked fine. The result is that I had six of eight cameras go live without a hitch. Two won't work despite every conceivable thing I have tried. Let me explain. First, I am not claiming to be an expert, but I am A+ and Network+ certified and have wired many, many networks over the past 20 years. That being said, I will focus on the two cameras that do not work. If I plug a camera in directly (bypassing the in-house cable runs), the cameras work fine. I have jumpered in a 100ft cable directly from the NVR to the cameras. They both work perfectly this way. So... pretty simply, it's the cable or terminations, right? Here's what I have checked. Cable length (TDR) is about correct (90 feet is the longest cable). Continuity is good. Wire-mapping is correct. POE matches other cables that work, Patch panel and patch cables are good. I have rewired everything on both ends (including wiring the cable onto a different patch panel port) twice now and it always comes up the same. I have checked meter readings from both ends - all match. Meter shows no shorts, no crossovers, no split pairs. I really want to figure this out. It makes absolutely no sense to me. These cameras "should" work, but don't. I have never seen a problem like this that couldn't be diagnosed. Besides, I paid a lot of money to have this place wired and if I can prove the installer did something wrong, I can take it back to him. The roofline on my house makes it darn near impossible to pull new cable without significant expense and labor. What is going on with my cables??? I'm stumped. Please, any insight would be greatly appreciated. Thank you very much. Dave in Trinity
  3. What's the easiest way to get a video clip from the Lorex HD to a thumb drive, my networked WDCloud, etc? I've done it once or twice in the past, but can't remember how. It was probably by use of the FLIR Cloud PC client, but that no longer works. I've installed the newer Lorex Cloud PC client but it won't accept the login credentials that work when I'm using the display & mouse connected to the DVR. Another approach would be to plug a thumb drive into to the DVR, but that's where I have the mouse plugged in. Any ideas?